Nova Deep Resin ND2410 [1.5 Gal Kit]

Nova Build recommends following all application instructions to ensure satisfactory results. The product should be between 75–80°F before use. The product container can be placed in warm water until it reaches the proper temperature. The ambient temperature should be between 75–80°F during the application and curing process and should be free of dust and other airborne contaminants. Before starting a project, make sure you have enough Deep ND2410 to complete it. Insufficient material may result in undesirable outcomes.

SEALING LAYER:
It's best to determine if your surface needs a sealer before starting your project. Sealers are important because porous or rough surfaces can develop air bubbles. Sealing the surface will help prevent air bubbles from adhering to it. Deep ND2410 can be used as a sealer. Porous or unsealed wood, such as tabletops, bars, hardwood, barn wood, knotty wood, or other types of wood, should be sealed before applying the pour. Well-seasoned or dried wood, such as barn wood or kiln-dried wood, may require multiple sealers. When pouring over aluminum, copper, stainless steel, plastic laminates, or other non-porous surfaces, a sealer is not necessary. Make sure these surfaces are clean and free of contaminants such as oil or grease. Allow any stain, varnish, or other coatings to dry completely before applying the sealer. Do not apply over oil-based finishes. Delicate objects, such as photographs, can be damaged by epoxy resin and should be sealed with an acrylic or polyurethane coating before being embedded with epoxy resin. If a sealing layer is needed, mix only a small amount of material, as it will cover a much larger area. Use a brush to spread a thin layer over the surface. Allow the sealing layer to dry for a minimum of 4–6 hours before applying the pouring layer.

BORDERS:
The pouring layer can be allowed to drip over the edges. Vertical edges won't be as thick as horizontal surfaces, so use a brush to ensure the coating is applied evenly to the edge. During the leveling and curing process, beads will form under the edge. Excessive beads can be removed before final curing using a flat putty knife. Hardened beads can be removed by sanding once the coating is fully cured.

AIR BUBBLE REMOVAL:
Allow the pour layer to level for 15 minutes after application before you begin removing air bubbles. Air bubbles are created by the mixing of the product, the application process, and surface tension, so it's completely normal to see them, but it's important to remove them. The best tools for removing air bubbles are a handheld propane torch or a heat gun. Hold the torch or heat gun about 6–10 inches from the coating and move it quickly across the surface. You'll see the air bubbles pop immediately. Continue this method every 10–15 minutes until all the bubbles are gone, which can take up to an hour. Avoid holding the torch too close to the coating and don't hold it in one area for too long, as you may burn yourself.

POUR LAYER:
To avoid pooling and an uneven layer of material, ensure the surface to be coated is as level as possible. The pouring layer can be applied up to 2 inches thick. If a thickness greater than 2 inches is desired, multiple coats will be necessary. Allow the pouring layer to cure for 16 to 24 hours before applying a second pouring layer. Apply the pouring layer starting at one end and pour the resin across the entire surface. Pour the mixed resin evenly onto the surface using a zigzag pattern. After pouring all the material, do not attempt to scrape additional material from the container. The material will begin to flow and level itself. If there are areas where more material has been poured, you can move it using a notched plastic trowel, putty knife, or foam brush.

ADDITIONAL LAYERS:
Allow the pouring coat to cure for 16 to 24 hours before applying a second pouring coat. If curing takes longer than 48 hours, lightly sand the surface with 220-300 grit sandpaper to ensure proper adhesion between coats. Clean the sanded surface with a tack cloth or a solvent, such as acetone or denatured alcohol, to remove any trapped sanding residue. Follow the pouring coat application instructions for each additional coat applied.

CURED:
After applying the final coat, the coating must be properly cured in a controlled, clean, dust-free environment at 75–80°F for 24–48 hours. Allow the coating to cure for a minimum of 5 days before full use.

Touch-Free: 24 – 36 hours
Complete Healing: 5 days

Depth->Thickness
1/8”->12.8 sq. ft/gal
1/4”->6.4 sq. ft/gal
1/2”->3.2 sq. ft/gal
3/4”->2.1 sq. ft/gal
1”->1.6 sq. ft/gal
1.5”->1 sq. ft/gal
2”->0.8 sq. ft/gal

Safety precautions must be strictly followed during storage, handling, and use. Personal protective equipment (PPE) must be worn at all times. PPE will include (but is not limited to): safety glasses with side shields and high-quality nitrile gloves.

JODVANA warrants that this product is free from material defects that affect its performance for a period of one year (from the date of purchase). JODVANA will replace, free of charge, the amount of coating that JODVANA determines has not performed, as the sole and exclusive remedy for any breach of this warranty and/or any other defect or failure of the coating. Proof of purchase is required. Labor costs for the application of any particular product are excluded. The warranty is void if JODVANA products are mixed or used in conjunction with materials that are substituted for JODVANA products. The warranty is not transferable.

ORDER PROCESSING: Please allow 24 business hours to process your order. You will receive an email within 48 hours to let you know your order is on its way.

STORE PICKUP - 2431 NW 21st Street Cape Coral FL 33993

Orders can be picked up Monday through Friday from 9 am to 5 pm. You will receive an email when your order is ready for pickup.

LOCAL DELIVERY

During checkout, enter your address and select your shipping option. Click the "Continue to Shipping" button. Local delivery is available for addresses within 25 miles of our store.

If the local delivery option does not appear during checkout, your order is not eligible for local delivery.

Orders eligible for local delivery placed before 12 pm during our business hours of 9 am to 5 pm will be delivered the same day. Orders placed outside of these hours will be delivered the next day we are open.

When your order is ready for delivery, you will receive an email with real-time tracking information.

FIXED RATE SHIPPING

Orders are generally shipped within 24 hours using FedEx . There is no flat shipping rate for orders shipped to locations outside the local region. We currently do not ship outside the United States.

NATIONAL SHIPPING RATES AND ESTIMATES

For calculated shipping rates: Shipping charges for your order will be calculated and displayed at checkout. Some specialized kits include free shipping due to the nature of the promotion. Estimated box prices vary depending on the number of boxes, estimated delivery time, and distance.